Log In

Inicio de sesión

¿Ha olvidado la contraseña?

Subtotal: €0.00

ESC KDE XF-UAS75HVC

Disponibilidad: Envío en 2 semanas aproximadamente

179,95 €
O BIEN

Descripción

High performance ESC system
Clic para ampliar y mover

The new UAS HVC series brings to life the next-generation of technology for UAS and Multi-Rotor operation; including an all-Aluminum 6061-T6 case for cool-running temperatures and rugged-construction, allowing the ESCs to be used in a wide-range of harsh environments and commercial/industrial applications (IP56 certification for all-weather operation).  The new series also comes pre-loaded with the latest production firmware, including these new, market-leading technologies:

  • Regenerative Braking – active braking during motor deceleration phase, providing instantaneous response to the flight controller commands and matched-response to acceleration profiles (less “float” during flight).
  • Temperature-Controlled Synchronous Rectification – new proprietary algorithm for smooth-running motors at low-throttle and improved, faster response under high-peak loads; all while significantly increasing flight-time efficiency and reducing operating temperatures (also termed "active-freewheeling").
  • Dynamic Timing and Startup Power – optimally-tuned for smooth and precision-controlled startup throughout the full-range of UAS Brushless Motors (no hesitation, stuttering, or response lag).
  • Increased Drive and Throttle Frequency Resolution – high-accuracy, linear throttle response throughout full-range of operation control.
  • Motor Synchronization – factory-calibrated ESCs for consistent throttle control and frequency-matched start-up protocols.

The UAS HVC series is compatible with 3S LiPo - 12S LiHV (55V Max) power systems - allowing for the next level of performance and efficiency for your UAS and Multi-Rotor applications.  In addition, the UAS HVC series includes active anti-spark circuitry, protecting the integrity and life-span of the critical connectors upon each initial plug-in and system power-up.

The series is tuned and optimized for the KDE Direct UAS Multi-Rotor Brushless Motor Series, for simple plug-and-play operation. No additional throttle calibration is required for most applications and settings are factory programmed.

ESCs include 200°C, 12 AWG silicone-wire power leads and 13 AWG silicone-wire motor leads with dual ф6.5mm (KDEXF-BC65) and ф4.0mm (KDEXF-BC40) 24K matching Bullet Connectors.

Programming: Proprietary Algorithm, 600Hz Refresh, Dynamic Advance Timing

Ingress Protection Rating: IP56 Certification

Features: Active Anti-Spark Circuit, Aluminum 6061-T6 Case

Includes:

  • Two (2) KDE Direct XF ф4.0mm 24K Bullet Connectors (Pair, KDEXF-BC40)
  • Two (2) KDE Direct XF ф6.5mm 24K Bullet Connectors (Pair, KDEXF-BC65)

Full Specifications:

Refresh Rate 600 Hz (50 - 600Hz Adaptive)
Maximum Peak Current 130 A (5 s)
Maximum Peak Power 5,770 W (5 s)
Maximum Continuous Current* 75+ A (180 s)
Maximum Continuous Power* 3,330+ W (180 s)
Maximum Efficiency > 98%
Voltage Range 11.1 V (3S LiPo) - 52.2 V (12S LiHV)
Internal BEC None (Opto-Isolation)
Maximum RPM 360,000 rpm (2-Pole)
PWM Rate Adaptive Dynamic Algorithm
Advance Timing 22° - 30° Dynamic Algorithm
ESC Size 37 mm (W) x 82 mm (L)
ESC Weight 78 g (114 g with Wires/Bullets)
Power Leads 12 AWG, 200°C
Motor Leads 13 AWG, 200°C
ESC Control Lead 22 AWG, 3-Wire JR (W-R-B)
ESC Programming Lead 22 AWG, 3-Wire JR (O-R-B)
Power Connects ф4.0 / ф6.5 mm Matched Pair
Motor Connects ф4.0 mm Female

*: ESC requires consistent airflow (5 mph or greater) across the heatsink to maintain maximum continuous current and power ratings during operation, specified at full-load condition (100% throttle). Increasing airflow or adding additional cooling can further increase the capabilities of the controller and extend the lifespan of the critical internal components.

Información adicional

Fabricante KDE

Te podría interesar también: